Beryl & Grandma

Over on the Scrapology Blog for the month of February we have been playing with Texture Paste.

We are scraplifting a beautiful layout by Heather Jacob

this is our sketch 

I used Kaiser Craft papers from the Periwinkle collection.

Ash Bazzill and some clear crystal gems.

The photo is an old one of Alan's cousin Beryl with their grandma Georgina. 

Here is a brief description of what I did

I kept the Ash Bazzill whole to make a firm base for the whole layout.

With 'Dawn' paper I punched down the right side with a border punch, then tore the other three sides so the finished piece was about 10" x 11".   I took the left over strip, turned it over, trimmed the ends so it was a little shorter than the first piece and place to left tucking it under the larger piece slightly.

Next I took the 'Whisper' paper and tore two strips approx. 3/4" x 10". This was placed horizontally across the layout under the photo.

With 'Hint' paper I trimmed one side with a deep edge border punch to create a lacy pattern. Then I cut a piece about 9 1/2" and added it just above the two horizontal strips of floral paper, setting the remainder aside for later.  I tore a piece - bird side up - about 1 1/2" x 9" which was tucked in vertically over the left side piece of black patterned paper and slightly under the main peach piece.

Next I made a tear up from the bottom on the right side and folded it back. Then I tore a scrap from the blue dot side of the 'Whisper' paper and tucked this under gap. I added a short piece of the left over lacy border punched earlier. I repeated this with a smaller tear low down on the left side and tucked under a torn piece of floral side of 'Whisper'. I tucked in a punched leaf frond using the black side of 'Hint' paper into the gap.

After inking all the torn edges I lightly stuck them in place. I decorated them with the sewing machine and some cream and black threads.  I further distressed the edges up to the stitching.

Using texture paste and mask I added some harlequin shapes to the top left area of the layout.  After allowing this to dry I inked it slightly to highlight the shapes, and texture.

I cut my photo mount from a plain peach area of 'Breath' paper.  I made a selection of label shapes in different papers and sizes cut using the Cricut and punches - these were cut up as only small amounts of each was needed to peek out from under the photo. I inked the edges and drew round the shapes with a pen.  After building up the arrangement I stuck everything in place.

I used Sizzlets Tattered Flower Garland decorative strip die, and cut leaves and flowers using 'Breath' paper. I used leaves from the aqua side and the flowers from the peach side.  I inked the edges of all these shapes, scrunched them up and stuck them in place. I added a gem to the centre of each flower.

I cut my letters for title with Sizzlets Typeset decorative strip die and stick this to the bottom left of page.

From the manufacture's strips at the bottom of each paper I cut three flags about 2" long. These were added to the right of the photo. about 1/2" apart. Three x 1/2" punched circles from some peach paper were inked and added to left of each flag with a 3D pad. A gem was added to each circle and coloured with sky blue Promarker. Then I added three more circles and gems to the top of two horizontal strips of paper. These were coloured with a spice Promarker. 

Finally I added a gem to each tear.

Thanks for looking.
Please pop over to Scrapology to find out more details for the challenge and the prize.

Christmas 1998 and a Double Layout

This is the double page I made for the 'T is for Texture' Scrapology challenge for January. I used photos of my family from Christmas 1998. Because the colours were so mixed I changed them all to sepia before printing them out.

This month we are scraplifting a layout by Stacey Hansen, called 'Life is a Highway', from September 2011 Creating Keepsakes Magazine. We are challenging you to use lots of texture (or lumpy bits), make a double layout and lots of photographs.

This is the original layout.

and our sketch

A closer look -

Left hand page

Right hand page 

I used:

2 sheets Red Bazzill cardstock

1 sheet Leapfrog Bazzill cardstock

1 sheet Salt Dotted Swiss Bazzill Cardstock

QuicKuts dies - Poinsettia, treelights, Lucy Alphabet

Creative Memories Large Circle Template

Technique Tuesday Cardstock Fundamentals

The patterned papers are American Crafts Christmas Dear Lizzy collection, Twinkling Tree, Gracious Gifts, Garland Greetings and Poinsettia and Pine.

Here is what I did:

Use the two pieces of red cardstock as a base for the double layout.

Cut two pieces of diagonal red white and green stripe, 4" x 12", use TT FUNdamental Postage Stamp template to draw pattern along the top of both pieces, just to mark where to cut, then using a small 5/8" circle punch cut notches in place.  Stick these to each piece of red about 2" up from the bottom so the pattern runs right across both pages, leave top unstuck to allow for tucking circle and bracket in place later.

Use a medium sized 'Swanky Frame' TT FUNdamental shape as a template. With Leapfrog cardstock cut half a frame following the outside edge of this shape. Cut a piece from holly paper using the inner frame as a guide. Mount the holly paper on top of the green, and tuck this under the diagonal striped paper on the right side of the layout to the right of this piece, about 3" down from the top. Trim where this overlaps the side of the layout.

Cut about 3/4 of a circle using the outer edge of the CM template and the fine stripe paper. Cut the inner circle from the dotted Swiss cardstock. Mount white over stripe and cut down the centre. Mount half of this shape on each side of the layout so they meet in the middle. See sketch for placement, but this is also about 3" down from the top. This is also tucked under the diagonal striped paper, and all is stuck down. (I wanted a little spare red cardstock for making flowers, so I gutted some from under where the circle is going to sit before sticking all down for this purpose!).

I ran a wide red grosgrain ribbon with a white stitch effect across the bottom of the diagonal striped paper, then added a 5mm green satin ribbon on top of this, with a green bow to the left side of the left page.

I matted all my photos in white and arranged them across the layout as in the sketch (roughly).

Then I dusted off the QuicKutz, which has been neglected since I acquired my Cricut!  I got busy and cut 16 poinsettia petals and 16 leaves, arranging these in pairs to make 8 flowers. I curved the petals with the scissor blade and attached each pair together with a gold brad, these were added to the layout with a 3D foam pad. The leaves were added later, 2 to each flower. Then I cut lots of small tree bulbs and arranged in a garland along the top of the layout, each of these is raised on a tiny piece of 3D foam too.

Next I cut my title using Leapfrog cardstock and the Lucy Alphabet dies. I arranged these letters inside the white circle.

Thanks for looking.

If you want more details of this challenge please go to the post titled 'T is for Texture' of 01/01/12 on the Scrapology blog.